1/16/2024 0 Comments Install cooltermSo, next thing was to mount it on the wall. Of course I had to take plenty of breaks! Doddi exorcised some bad spirits from the apartment?Įxperimenting with Coolterm, I got the motors spinning and I experimented with some G-code commands and stuff started working! It only happened once again and then no more troubles. I found out that the power supply must create a surge of some sorts, as it once more tripped the circuit breaker. Following the TinyG wiki, linked above, I setup Coolterm and was able to connect to the TinyG!Ĭoolterm (screencapped after diconnecting the device)īack at it at home, I made sure everything still worked. I started the 3D printing of the objects and mounted the motors to the plate, once cut. Doddi that the TinyG was perfectly fine, as was the power supply. And it still is, as I received a communication later that day from Mr. The Westfjords have a long history of magic, witchcraft and wizardry. I’m not joking, but I saw Doddi reciting a powerful incantation to the board, waving his right hand ever so slightly above it. Later, I brought the TinyG and the power supply back to the Fab Lab. It also has three holes in the center, which should take screws to hold the pen. I used this model to make the servo mount. Also, being optimistic, I designed it with a servo holder! I basically just made a shape that I thought would be good. I made a guesstimate of the axle size so the center hole is too tight.Īlso, the “walls” should be higher, as the string I used can slip over them. It has two mounts for the motors and plenty of other holes for various wall mounting possibilities. I made the plate to a size that would fit the laser cutter, a width of 55cm. So, instead of throwing my self in a huge pit of despair and misery, I started a Fusion 360 session and made the following items: Have you heard of “ Þetta reddast”? If not, just know that most often, it will reddast! Why must everything turn against me? Well, I contacted Doddi and he put the word out that we might be in the need of some stepper motor controllers. Was it fried? I smelled nothing bad, nor was I able to spot anything. Now the circuit breaker held fine, but the TinyG was unresponsive. I connected the TinyG again and powered it up. I turned of the device, disconnected the wires reset the breaker. Púúffff! The power went out! What! WHAT? I checked the apartments mains fuse box and one of the circuit breaker was tripped! Well hot damn! I double-checked my polarities and powered on the supply. Establish a serial connection to the TinyG and verify communication before wiring motors.Make sure you have FTDI drivers installed.Looking at the Connecting the TinyG part, they mention a few things. I knew I needed a power supply to power the TinyG, but before getting a head of myself, I checked out the TinyG wiki. Once the Paw Patrol powers started to dwindle, I ransacked the Fab Lab for equipment and back to my temporary dwelling where I set up my work area. We decided to try and see if we could get the TinyG working and get the motors moving. Doddi being a hands-on type of guy, he showed me the basic idea behind a wall drawing plotter. Doddi and I could discuss the mission at hand. FabLabIsa and he is my lovely instructor!įirst thing we did was to engage the hypnotic powers of Paw Ísafjörður - Childcare For the ones not on a nickname-knowing-level with Doddi, he is also known as Þórarinn Bjartur Breiðfjörð Gunnarsson, a.k.a. Once I had arrived in Ísafjörður and had settled in a bit, I payed Mr. Among those, Nema 17 stepper motors, a Tinyg module and some servos. ¶īefore leaving Akureyri, I grabbed some stuff from my lab. Enough with the excuses, let’s get on with it. Grrrrreat start! /sĪnd it being easter time and there being a festival at Ísafjörður, it was quite busy for my wife, which meant I was quite busy with the children! (Video link 1 and 2 (possible geo-blocking, sorry!)). Then it was the drive to Ísafjörður, just under 600kms with a toddler and the lingering effect of the virus. The start was rough, as I had caught the Influenza virus which pretty much knocked me out. We chose Ísafjörður so that I could try and spend some time with my instructor. A few months ago it was decided that my family and I would travel to Ísafjörður for these two weeks, where my wife would do contract work. Machine week, which is extended with an easter break. Invention, Intellectual Property, and Incomeġ2. Enough with the excuses, let's get on with it.ġ5.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |